1
00:00:09,166 --> 00:00:12,041
OK, I'm going to move on to the other side of the room now.

2
00:00:12,041 --> 00:00:15,041
Now I know in there, but these lengths of skirting

3
00:00:15,041 --> 00:00:18,000
aren't long enough
to go completely along the side of that wall.

4
00:00:18,458 --> 00:00:22,500
So what are we going to do is what we call
the lengthening joint, and the best place

5
00:00:22,500 --> 00:00:24,833
to put a lengthening joint is in the furthest away,

6
00:00:25,708 --> 00:00:27,833
but also do it so you don't.

7
00:00:28,250 --> 00:00:32,083
The joint isn't highlighted from the doorway
as you walk in.

8
00:00:33,291 --> 00:00:35,375
So I'm just going to take this length here.

9
00:00:36,208 --> 00:00:38,041
Same as I did the other side

10
00:00:39,958 --> 00:00:41,375
mark off the height

11
00:00:42,750 --> 00:00:44,250
of what I've got.

12
00:00:52,125 --> 00:00:53,500
Then use

13
00:00:54,625 --> 00:00:56,625
something with that same profile.

14
00:00:58,583 --> 00:01:00,583
To draw around.

15
00:01:06,458 --> 00:01:07,500
And I'm going to.

16
00:01:12,625 --> 00:01:13,875
Just cut that piece out.

17
00:01:15,750 --> 00:01:17,000
We'll use a big saw.

18
00:01:35,750 --> 00:01:38,750
Just remember, if you're in a house somewhere
when you flip this stuff over

19
00:01:38,750 --> 00:01:40,875
that you don't knock anything off or anything over.

20
00:01:42,500 --> 00:01:45,250
Then just use a coping saw follow my profile around.

21
00:01:59,083 --> 00:02:04,000
I've got this blade on what they call the pull,
so it's on the backward stroke that it's cutting,

22
00:02:04,000 --> 00:02:06,958
you can turn those around the other way
and have it on the push if you wish.

23
00:02:08,666 --> 00:02:10,916
I've got the length there and what I'm going to do now

24
00:02:11,583 --> 00:02:13,125
is put a mitre on it.

25
00:02:17,375 --> 00:02:20,125
So I'm just going to put a mitre on in that direction.

26
00:02:48,166 --> 00:02:50,416
So there I've got the joint for the corner

27
00:02:51,791 --> 00:02:53,208
and the mitre section.

28
00:02:55,291 --> 00:02:57,375
Now, I'm just going to fix that one in place.

29
00:03:08,125 --> 00:03:11,416
So just putting that on there,
just be careful with your hammer.

30
00:03:11,416 --> 00:03:13,125
If it does slip off the nails.

31
00:03:13,125 --> 00:03:17,208
It may be the fact that the face of your hammer
is dirty, so just give it a bit of a clean

32
00:03:17,208 --> 00:03:20,541
with a bit of sandpaper
and it won't slip off the nails then.

33
00:03:23,833 --> 00:03:25,250
I'm then going to grab a

34
00:03:27,166 --> 00:03:27,958
new length.

35
00:03:32,208 --> 00:03:36,333
And if I put that into the corner.

36
00:03:37,708 --> 00:03:39,500
Tight up there.

37
00:03:40,750 --> 00:03:44,750
I can then mark off the full length.

38
00:03:47,708 --> 00:03:49,000
On there.

39
00:03:53,666 --> 00:03:56,000
Mark which way the direction the mitre is going to go.

40
00:04:05,833 --> 00:04:08,041
And using my square just to make sure I get it

41
00:04:08,958 --> 00:04:10,125
in the right place.

42
00:04:11,875 --> 00:04:13,000
I'll turn it over back.

43
00:04:14,375 --> 00:04:16,916
Because of the molding I'm
just going to turn it from the back side

44
00:04:18,791 --> 00:04:20,750
and transfer that to the front.

45
00:04:38,333 --> 00:04:43,708
And then I can cut my mitre on there.

46
00:05:15,375 --> 00:05:17,541
Very difficult, then, to notice from the doorway,

47
00:05:19,500 --> 00:05:21,458
there's actually a joint in.

48
00:05:22,583 --> 00:05:25,541
That length of skirting at that point.

49
00:05:35,583 --> 00:05:36,916
I can add a few.

50
00:05:36,916 --> 00:05:41,208
You can see this one's nice and tight down on the floor.