1
00:00:09,083 --> 00:00:13,583
OK, just going to make the shorter pieces now
and, I've noticed on this length

2
00:00:13,583 --> 00:00:16,583
that we've got a few splits and cracks in it,
but I can use.

3
00:00:17,833 --> 00:00:20,250
Sort of that bit there.

4
00:00:20,250 --> 00:00:24,125
And some of the other end to fill in these smaller
areas.

5
00:00:25,916 --> 00:00:27,583
I'm just going to cut.

6
00:00:31,833 --> 00:00:33,666
A little bit off the end here 

7
00:00:35,416 --> 00:00:37,083
To use.

8
00:00:46,833 --> 00:00:49,000
I'm just going to cut that straight for a minute.

9
00:00:58,375 --> 00:01:01,375
Now I'm going to work in the corner to cut an external mitre.

10
00:01:02,958 --> 00:01:05,291
So if I bring a piece for the one and a piece
for the other.

11
00:01:12,208 --> 00:01:13,958
To mark this one out,

12
00:01:16,708 --> 00:01:18,750
I just draw a line across the floor

13
00:01:20,250 --> 00:01:21,583
off that wall,

14
00:01:23,041 --> 00:01:26,625
a line off that wall.

15
00:01:28,000 --> 00:01:30,208
That gives me the outside point of my mitre,

16
00:01:31,333 --> 00:01:33,166
because that's more the critical point.

17
00:01:34,166 --> 00:01:37,000
I'm just going to mark out
where that line comes on that one.

18
00:01:39,375 --> 00:01:41,625
And mark where the line comes.

19
00:01:43,583 --> 00:01:44,833
On that one.

20
00:01:50,583 --> 00:01:54,958
I am going to use the square just to square those up,

21
00:01:54,958 --> 00:01:56,750
so I've got somewhere to.

22
00:02:01,375 --> 00:02:03,708
Aim my chop saw for.

23
00:02:11,666 --> 00:02:13,541
So I know that one is going to go one way.

24
00:02:13,541 --> 00:02:15,125
One's got to go the other way.

25
00:02:16,166 --> 00:02:17,250
So this one.

26
00:02:19,958 --> 00:02:21,625
In that direction.

27
00:02:53,583 --> 00:02:58,208
A nice external mitre on that piece.

28
00:02:58,208 --> 00:03:01,500
Now I need to turn the other one in the opposite direction.

29
00:03:03,625 --> 00:03:06,250
These have got set points that will lock in 

30
00:03:06,250 --> 00:03:09,750
Again I don't always accurately cut straight the line the first time

31
00:03:09,750 --> 00:03:13,791
I just work myself gently up to it to make sure I'm in the right position.

32
00:03:34,208 --> 00:03:36,250
So you've got the other mitre.

33
00:03:37,250 --> 00:03:39,000
So I'll drop these two on the corner.

34
00:03:45,250 --> 00:03:47,291
A nice mitre there.

35
00:04:04,708 --> 00:04:08,583
And what I can do is just put a nail in the mitre.

36
00:04:17,583 --> 00:04:19,916
Just to hold that.

37
00:04:25,125 --> 00:04:26,916
Two in one way.

38
00:04:33,625 --> 00:04:35,375
One in the other way.

39
00:04:36,666 --> 00:04:38,708
And then we've got the external mitre.

40
00:04:39,666 --> 00:04:44,208
Then all I need to do is repeat a scribe
into that corner and a scribe into that corner.