1
00:00:09,750 --> 00:00:12,000
As you can see, I've done

2
00:00:12,875 --> 00:00:15,041
a straight cut into that corner.

3
00:00:16,083 --> 00:00:18,541
Don't do a mitre on the inside corners

4
00:00:18,541 --> 00:00:22,291
because you can't guarantee
the corners are 90 degrees.

5
00:00:23,000 --> 00:00:26,708
And if you do a mitre,
if it's out it's either going to close up

6
00:00:26,708 --> 00:00:29,416
and have a gap at the back or open out
and have a gap in the front.

7
00:00:29,958 --> 00:00:32,583
So what we do is what we call a scribe joint.

8
00:00:33,333 --> 00:00:35,458
And I'll show you how we set out for a scribe.

9
00:00:35,750 --> 00:00:37,708
So I just want a piece a little bit bigger than that.

10
00:00:37,708 --> 00:00:40,583
So I'm looking for something like 400 mm long.

11
00:00:40,583 --> 00:00:42,500
So to do a scribe.

12
00:00:45,375 --> 00:00:47,166
I'm actually going to cut.

13
00:00:51,791 --> 00:00:53,666
A 45 on that corner

14
00:00:54,166 --> 00:00:56,750
and if I use a chop saw
I wouldn't have to mark it out.

15
00:00:56,750 --> 00:00:58,458
This is where we use our mitre square.

16
00:01:00,000 --> 00:01:01,583
45 across there.

17
00:01:01,583 --> 00:01:04,208
And just so we can get it,
because its difficult with the curve.

18
00:01:05,541 --> 00:01:07,750
You come back off the bottom.

19
00:01:08,500 --> 00:01:10,291
From that side,

20
00:01:11,541 --> 00:01:14,375
mitre it in the direction you want to cross that side.

21
00:01:16,375 --> 00:01:19,125
We'll take the line up there.

22
00:01:22,125 --> 00:01:24,041
That will give me my line.

23
00:01:24,041 --> 00:01:25,375
So now I'm going to cut that.

24
00:01:29,833 --> 00:01:32,583
So just move this saw around to 45 degrees.

25
00:01:34,041 --> 00:01:35,833
I'm sure it's going to cut that corner.

26
00:01:46,541 --> 00:01:48,916
So even though I've cut a mitre,

27
00:01:48,916 --> 00:01:52,250
obviously I'm going to cut that,
so I can fit that against a square edge.

28
00:01:56,416 --> 00:01:58,333
So that actually gives me the outline.

29
00:01:59,958 --> 00:02:02,208
Following that edge round of my molding.

30
00:02:03,625 --> 00:02:07,500
so I do the same for whatever molding
I showed you earlier.

31
00:02:07,500 --> 00:02:10,500
You do exactly the same process
for doing an internal corner.

32
00:02:12,666 --> 00:02:13,833
Now I've got to cut off-

33
00:02:15,458 --> 00:02:16,708
I can cut this bit off straight,

34
00:02:17,708 --> 00:02:20,083
so using my saw.

35
00:02:20,416 --> 00:02:22,125
You don't have to cut it square, you can cut it back.

36
00:02:22,125 --> 00:02:24,250
So take the back out of it.

37
00:02:27,708 --> 00:02:30,000
And just carefully cut down.

38
00:02:34,833 --> 00:02:37,000
Till I get to the curve

39
00:02:38,208 --> 00:02:40,833
and now using my coping saw.

40
00:02:42,166 --> 00:02:43,875
I'm just going to.

41
00:02:44,916 --> 00:02:45,916
Cut around.

42
00:02:48,166 --> 00:02:50,750
Follow that curve round.

43
00:03:16,875 --> 00:03:18,208
I'll show you with the off cut.

44
00:03:19,375 --> 00:03:20,916
When I put those two together.

45
00:03:23,000 --> 00:03:24,791
It looks like a mitre.

46
00:03:24,791 --> 00:03:27,875
But if it's a little bit out in a corner.

47
00:03:27,875 --> 00:03:29,416
You've got that little bit of play

48
00:03:29,416 --> 00:03:31,458
that you can use to get a good fit on the corner.

49
00:03:33,333 --> 00:03:35,125
I'm now going to mark that to length,

50
00:03:36,125 --> 00:03:38,333
so I'm going to offer that into the corner piece.

51
00:03:42,208 --> 00:03:44,250
And now it's got a tight joint I'm going to mark off

52
00:03:44,250 --> 00:03:46,875
where my length of my architrave comes

53
00:03:48,250 --> 00:03:50,708
and I can cut that piece off.

54
00:03:57,833 --> 00:03:59,666
Tap that into place,

55
00:04:00,708 --> 00:04:02,416
then I can get the fixing in.

56
00:04:06,833 --> 00:04:10,125
And I can go around afterwards just with a nail punch just punch all these nails in,

57
00:04:11,000 --> 00:04:13,541
get it ready for the painter.

58
00:04:19,375 --> 00:04:20,958
That's one of side of the room done