1
00:00:09,333 --> 00:00:12,375
So we've got the first drop of paper hung,

2
00:00:13,041 --> 00:00:17,416
so now we're going from your perspective
 from the right, round the corner.

3
00:00:18,583 --> 00:00:22,166
Piece of paper is about 53 centimeters

4
00:00:23,458 --> 00:00:25,708
or 530 millimeters. 

5
00:00:25,708 --> 00:00:29,416
We only need 35 centimeters
 to take us around the corner.

6
00:00:30,000 --> 00:00:33,666
So rather than paste the whole thing
 and then try and cut off

7
00:00:33,666 --> 00:00:36,875
a great big section,
 I've actually cut this to size

8
00:00:37,875 --> 00:00:41,166
after I pasted it. So again. 

9
00:00:41,166 --> 00:00:45,375
Peel away the first few inches,
 so we don't get the two comedy corners,

10
00:00:46,666 --> 00:00:48,083
let the paper unravel. 

11
00:00:48,083 --> 00:00:51,833
Taking care not to allow the paste
 to come in contact with the floor

12
00:00:51,833 --> 00:00:53,916
or the wall and then.

13
00:00:55,000 --> 00:00:59,458
Offer this piece of paper up to the bit
 that's already hung, and again, my right

14
00:00:59,458 --> 00:01:03,958
hand, the hand that's holding
 the paper is close to the wall. Alright.

15
00:01:04,250 --> 00:01:09,458
And as high as it can be
 to support the paper, so I get to the top.

16
00:01:10,875 --> 00:01:12,750
Get the butt joint sorted.

17
00:01:14,000 --> 00:01:16,458
Go back and again, 

18
00:01:16,458 --> 00:01:17,916
little bit of contact with the ceiling. 

19
00:01:17,916 --> 00:01:20,833
I've come quite low this time,
 it doesn't matter, still enough to trim.

20
00:01:23,500 --> 00:01:27,041
And smooth that out
 and just gently make sure

21
00:01:27,416 --> 00:01:30,166
the two pieces of paper are just touching

22
00:01:30,833 --> 00:01:33,625
what we need to avoid. 

23
00:01:34,000 --> 00:01:38,833
Is an overlap. When that dries
 that would be an obvious ridge.

24
00:01:39,166 --> 00:01:41,750
And then when you paint it,
 it would then emphasise that ridge.

25
00:01:42,083 --> 00:01:46,541
So we need to avoid the overlap
 just as much as we need to avoid the gap,

26
00:01:47,000 --> 00:01:50,208
because again, when that's painted,
 we then have a valley in miniature.

27
00:01:50,958 --> 00:01:55,416
So just make sure
 the two pieces of paper meet.

28
00:01:57,041 --> 00:02:00,250
Now, I've caused a crease
 by doing that, though, no big issue.

29
00:02:01,000 --> 00:02:03,833
Gently lift the paper. 

30
00:02:05,875 --> 00:02:08,708
And just realign the joint.

31
00:02:08,708 --> 00:02:12,000
Don't make a habit of doing that
 it does stretch the paper,

32
00:02:12,000 --> 00:02:15,000
and that makes it harder
 to get the joints accurate. Alright.

33
00:02:17,375 --> 00:02:19,708
And down we go, just as we did before.

34
00:02:25,208 --> 00:02:26,375
Right, smoothing out, 

35
00:02:26,375 --> 00:02:28,916
then from side to side. 

36
00:02:35,083 --> 00:02:37,500
So having undone the bottom fold,

37
00:02:37,500 --> 00:02:41,125
that quarter, remember
 this is a three quarter fold.

38
00:02:41,666 --> 00:02:44,291
The three quarter
 being the longer part, goes at the top.

39
00:02:44,750 --> 00:02:47,375
So we just undo the final quarter

40
00:02:48,541 --> 00:02:53,125
and. As always, just smoothing
 at the bottom with your fingernails.

41
00:02:53,541 --> 00:02:56,541
Now then, if we just focus
 on this bottom corner,

42
00:02:57,208 --> 00:02:58,666
this'll happen at the top as well. 

43
00:02:58,666 --> 00:03:02,875
If we try and push rounds before
 we've cut it, it just pulls back again.

44
00:03:03,291 --> 00:03:06,875
Alright. But around the corner,
 we must go because we need our overlap.

45
00:03:07,250 --> 00:03:09,750
So before we do that

46
00:03:10,041 --> 00:03:14,541
I can just put the little cut in to the
 corner if I want you to get

47
00:03:17,750 --> 00:03:18,541
If I wanted to go 

48
00:03:18,541 --> 00:03:21,583
around straight away
 or I could wait until I've trimmed it,

49
00:03:22,000 --> 00:03:25,375
but all the time that that is attached,
 we are not going around the corner.

50
00:03:26,083 --> 00:03:28,583
So formed my crease again

51
00:03:31,333 --> 00:03:33,541
or just for a change, 

52
00:03:33,541 --> 00:03:36,833
I could put a pencil line across. 

53
00:03:40,083 --> 00:03:41,916
Gently lift away 

54
00:03:41,916 --> 00:03:46,666
and cut along the crease or pencil line,
 whichever you prefer.

55
00:03:47,333 --> 00:03:50,125
As I've said before,
 both methods do work well,

56
00:03:51,250 --> 00:03:53,750
but you obviously do need the light
 if you're following a crease

57
00:03:55,250 --> 00:03:58,166
and then just dab in
 and I'll just trim off the top

58
00:03:58,166 --> 00:04:02,125
in a minute and again
 wipe down the top and the bottom.

59
00:04:02,541 --> 00:04:04,208
And then we will go around the corner.