1 00:00:09,333 --> 00:00:12,375 So we've got the first drop of paper hung, 2 00:00:13,041 --> 00:00:17,416 so now we're going from your perspective from the right, round the corner. 3 00:00:18,583 --> 00:00:22,166 Piece of paper is about 53 centimeters 4 00:00:23,458 --> 00:00:25,708 or 530 millimeters. 5 00:00:25,708 --> 00:00:29,416 We only need 35 centimeters to take us around the corner. 6 00:00:30,000 --> 00:00:33,666 So rather than paste the whole thing and then try and cut off 7 00:00:33,666 --> 00:00:36,875 a great big section, I've actually cut this to size 8 00:00:37,875 --> 00:00:41,166 after I pasted it. So again. 9 00:00:41,166 --> 00:00:45,375 Peel away the first few inches, so we don't get the two comedy corners, 10 00:00:46,666 --> 00:00:48,083 let the paper unravel. 11 00:00:48,083 --> 00:00:51,833 Taking care not to allow the paste to come in contact with the floor 12 00:00:51,833 --> 00:00:53,916 or the wall and then. 13 00:00:55,000 --> 00:00:59,458 Offer this piece of paper up to the bit that's already hung, and again, my right 14 00:00:59,458 --> 00:01:03,958 hand, the hand that's holding the paper is close to the wall. Alright. 15 00:01:04,250 --> 00:01:09,458 And as high as it can be to support the paper, so I get to the top. 16 00:01:10,875 --> 00:01:12,750 Get the butt joint sorted. 17 00:01:14,000 --> 00:01:16,458 Go back and again, 18 00:01:16,458 --> 00:01:17,916 little bit of contact with the ceiling. 19 00:01:17,916 --> 00:01:20,833 I've come quite low this time, it doesn't matter, still enough to trim. 20 00:01:23,500 --> 00:01:27,041 And smooth that out and just gently make sure 21 00:01:27,416 --> 00:01:30,166 the two pieces of paper are just touching 22 00:01:30,833 --> 00:01:33,625 what we need to avoid. 23 00:01:34,000 --> 00:01:38,833 Is an overlap. When that dries that would be an obvious ridge. 24 00:01:39,166 --> 00:01:41,750 And then when you paint it, it would then emphasise that ridge. 25 00:01:42,083 --> 00:01:46,541 So we need to avoid the overlap just as much as we need to avoid the gap, 26 00:01:47,000 --> 00:01:50,208 because again, when that's painted, we then have a valley in miniature. 27 00:01:50,958 --> 00:01:55,416 So just make sure the two pieces of paper meet. 28 00:01:57,041 --> 00:02:00,250 Now, I've caused a crease by doing that, though, no big issue. 29 00:02:01,000 --> 00:02:03,833 Gently lift the paper. 30 00:02:05,875 --> 00:02:08,708 And just realign the joint. 31 00:02:08,708 --> 00:02:12,000 Don't make a habit of doing that it does stretch the paper, 32 00:02:12,000 --> 00:02:15,000 and that makes it harder to get the joints accurate. Alright. 33 00:02:17,375 --> 00:02:19,708 And down we go, just as we did before. 34 00:02:25,208 --> 00:02:26,375 Right, smoothing out, 35 00:02:26,375 --> 00:02:28,916 then from side to side. 36 00:02:35,083 --> 00:02:37,500 So having undone the bottom fold, 37 00:02:37,500 --> 00:02:41,125 that quarter, remember this is a three quarter fold. 38 00:02:41,666 --> 00:02:44,291 The three quarter being the longer part, goes at the top. 39 00:02:44,750 --> 00:02:47,375 So we just undo the final quarter 40 00:02:48,541 --> 00:02:53,125 and. As always, just smoothing at the bottom with your fingernails. 41 00:02:53,541 --> 00:02:56,541 Now then, if we just focus on this bottom corner, 42 00:02:57,208 --> 00:02:58,666 this'll happen at the top as well. 43 00:02:58,666 --> 00:03:02,875 If we try and push rounds before we've cut it, it just pulls back again. 44 00:03:03,291 --> 00:03:06,875 Alright. But around the corner, we must go because we need our overlap. 45 00:03:07,250 --> 00:03:09,750 So before we do that 46 00:03:10,041 --> 00:03:14,541 I can just put the little cut in to the corner if I want you to get 47 00:03:17,750 --> 00:03:18,541 If I wanted to go 48 00:03:18,541 --> 00:03:21,583 around straight away or I could wait until I've trimmed it, 49 00:03:22,000 --> 00:03:25,375 but all the time that that is attached, we are not going around the corner. 50 00:03:26,083 --> 00:03:28,583 So formed my crease again 51 00:03:31,333 --> 00:03:33,541 or just for a change, 52 00:03:33,541 --> 00:03:36,833 I could put a pencil line across. 53 00:03:40,083 --> 00:03:41,916 Gently lift away 54 00:03:41,916 --> 00:03:46,666 and cut along the crease or pencil line, whichever you prefer. 55 00:03:47,333 --> 00:03:50,125 As I've said before, both methods do work well, 56 00:03:51,250 --> 00:03:53,750 but you obviously do need the light if you're following a crease 57 00:03:55,250 --> 00:03:58,166 and then just dab in and I'll just trim off the top 58 00:03:58,166 --> 00:04:02,125 in a minute and again wipe down the top and the bottom. 59 00:04:02,541 --> 00:04:04,208 And then we will go around the corner.